Features

• S
  
  iTECH Control
  

  A MULTI-FUNCTION UNIT ENABLING SPEED CONTROL TYRE SAVING AND IDLE SHUTDOWN FROM THE SAME UNIT! 

  
  
  This product conforms to
  
  Transmon`s stand-alone iTEch Tyre and iTEch Gear systems have been discontinued because they can now be combined with each other and the Speed 6 system to create a multi-purpose unit which gives the same functionality for a fraction of the cost!
  
  Each function is still available individually at the same cost as the old systems but we can now offer discounts on combinations of two or more functions as there is no additional unit to be fitted. This saves fitting time space inside the truck and cost to the customer.
  
  Speed
  Detects that the truck is moving and
  
  KPA2 code entry
  

  THE KPA2

  
  

  INCREASES SITE SAFETY AND SECURITY BY LIMITING IGNITION ACCESS TO AUTHORISED OPERATOR

  
  

  IC Trucks:

  A valid operator code is entered on the keypad and the interface unit activates the ignition system. Pressing `P` operates the starter and pressing `P` again stops the engine.
  
  

  Electric Trucks:

  On electric plants operating the truck push-stop safety switch will switch off the machine.
  

  Features

  
  

  • Separate interface unit for security and easy installation
  • Surface mounted - needs no back box
  • Suitable for IC and Electric equipment
  • Push button Start/Stop if required.
  • Can be used with or without vehicle keyswitch
  • Hard-wearing and waterproof Stainless Steel keypad
  • 50
    
    Over Speed Detection
    

    WARNS THE OPERATOR WHEN A PRE-SET SPEED LIMIT IS EXCEEDED

    
    The system monitors the travel speed of any IC engine powered forklift truck and indicates when a set speed has been exceeded. The system does not govern the engine and can be set to the required speed limit to suit the specific application requirements.When the truck reaches the set speed limit it will automatically activate a beacon on top of the truck a buzzer and an LED both fitted in the cab.When the truck speed drops below the set speed limit the unit will reset and warnings will cease. The system does not affect the performance of the truck as it is designed to act as a warning only.
    
    

    Features

    
    

    • Suitable for Gas Diesel & Electric trucks
    • Recommended for forklift truck operating areas that are used by pedestrians
    • Fully adjustable works in for
      
      Over-Load Detection
      

      ENHANCES SITE SAFETY AND REDUCES DAMAGE BY WARNING THE OPERATOR THAT THE LOAD LIMIT HAS BEEN REACHED

      
      The system warns the operator that a pre-set lifting pressure limit has been exceeded. The system is fully adjustable and any level can be set within the limits of the 250 bar pressure transducer fitted within the load cell. Site safety is improved and hydraulic lifting performance is not affected.
      
      If the operator attempts to lift above the pre-set pressure a warning signal is given via a buzzer and a beacon situated on the truck to alert the operator.
      
      Level 1
      No display basic switch only - just alerts operator if over maximum.
      
      Level 2
      Display included shows actual weight and alerts operator if over maximum.
      

      Features

      
      

      • Suitable for all vehicles
      • Triggers alar
        
        Pedestrian Warning System
        

        IMPROVE SAFETY BY MAKING FORKLIFT OPERATORS AWARE OF NEARBY HAZARDS

        Although fork lift trucks can be very useful pieces of work equipment they are also very dangerous and are to blame for more serious accidents at work than cars and HGV`s combined.
        
        
        According to statistics every day of the year a British worker needs hospital treatment after being injured by a fork lift truck and one worker is killed every six weeks as a result of accidents involving them. Many more suffer very serious injuries.
        
        
        In partnership with SiteZone Safety Transmon Engineering Ltd can offer an Active RFID  Proximity Alert system able to detect personnel and objects within a pre-determined safety zone around v
        
        Power Saver
        

        REDUCES FUEL OR POWER USAGE AND PROTECTS THE ENGINE BY AUTOMATICALLY SHUTTING DOWN AN IDLE TRUCK

        
        The iTEch Power System automatically shuts down a truck that is not being used. The length of time a truck can stand idle is adjustable from 1 to 8 minutes in four steps. The device helps to reduce fuel or battery usage and engine wear caused by excessive idle time. It also helps to protect the engine preventing premature servicing.
        
        

        Features

        
        

        • Simple installation
        • Shuts down engines to save fuel / conserve battery power
        • Idle shut down delay - select 1 2 4 or 8 minutes

        Benefits

        
        

        • Reduced fuel bill
        • Reduced engine wear
        • Reduced non-operational run hours and servicing

        
        Radar Speed Zoning
        

        TRANSMON RADAR BASED SPEED ZONING

        
        

        TRUCK BASED SPEED ZONING FOR INDOOR / OUTDOOR APPLICATIONS

        
        Transmon Engineering now have a radar based speed zoning option. This truck mounted sensor in slimline and unobtrusive and is ideally mounted on the roof of the forklift truck. The sensor detects roof height so will know when the forklift truck is indoors and when it is outdoors.
        

        
        

        
        The sensor works via roof height detection without being obscured by outdoor objects such as overhead cranes. The sensor then communicates with either the trucks on board speed control or one of our own designed and manufactured speed controls: RSPC1 - for mechanical speed control or iTEch control - for electronic throttle pedals. This will then allow the truck to have 2 safety spe
        
        Red LED Line Alert
        

        FURTHER ENHANCE SITE SAFETY BY PROVIDING A VISUAL WARNING TO PEDESTRIANS

        
        Our range of forklift truck safety lighting is ever expanding the already successful blue LED spot light has now been partnered with our red LED side line alert.
        
        Transmon now offers a bright rugged and flexible red LED line light which provides a visual warning alerting pedestrians that they are too close to the forklift truck. The system is ideally suited to trucks operating in warehouse aisles or unclear cross-over areas and for operations requiring pedestrians and forklift trucks to operate safely alongside each other.
        
        The light is resistant to shock vibrations and moisture and the LED technology offers high light output while maintaining a low current draw.
        
        Unlike audible warning devices pedestrians and other drivers can see instantly where the trucks is and in which direction it is travelling and many drivers and employees have expressed an improved accep
        
        Road Speed Control
        

        ENHANCES SITE SAFETY BY LIMITING THE FORKLIFT TRUCKS TRAVEL SPEED

        
        

        This product conforms to
        
        

        The new iTEch Speed v2 has been designed to limit the travel speed of a forklift truck with a cable-operated throttle by detecting that the truck is travelling above a pre-set speed and then applying a throttle restriction to limit the truck speed. As long as the truck is travelling below the pre-set speed lifting is not affected.
        
        The unit can be programmed with two separate speeds which can be switched by for example the directional selector (giving a slower speed in reverse than forward) a key switch where the Supervisor holds the key or our iTEch Zone or Proximity Alert systems. Due to its ability to give a proportional restriction (where if the speed begins to drop the limit is relaxed gradually) the climbing of
        
        Sequential Seat Belt System
        

        INCREASES SITE SAFETY BY PROMPTING THE OPERATOR TO CONNECT THEIR SEAT BELT OR DRIVE WILL BE PROHIBITED

        
        The Sequential Seatbelt Startup System is designed to alert the operator if the seatbelt is not connected or has been disconnected during use. It can also be used to disable vehicle functionality such as interrupt drive or prevent vehicle ignition.
        
        An audible buzzer and a visual lamp are mounted in the cab to alert the operator. Off truck personnel are alerted via an external flashing red beacon.
        
        The only means of deactivating the warning during use is to replace the seatbelt strap in to the clasp. The warning devices all remain active whilst the seatbelt is not fastened and the truck is in use.
        
        Seat belts can also be used in conjunction with our TDS601 fleet management system which has the ability to enforce correct seatbelt use and record non-compliance.
        
        The system uses the following method to determine whether the seat b
        
        Smart Eye
        

        SMART EYE

        
        

        HELPS TO ENHANCE SITE SAFETY THROUGH DRIVER ACCOUNTABILITY BY RECORDING DRIVING INCIDENTS

        
        A vehicle-mounted camera and recording unit enables management to review incidents that have occurred in the work place automatically storing the recorded footage from shortly before the impact to shortly after.
        
        A simple USB connection allows a fast data download using any PC or laptop and the footage can be viewed in detail using the supplied software.
        

        Features

        
        

        • Wide-angle lens
        • Impact or button press triggers capture of 15 seconds before and 15 seconds after incident
        • Optional continuous recording mode for 2 - 16 hours (depending on memory card capacity)
        • On-board GPS provides location speed plots the event and shows route<
          
          Speed Safety Zone
          

          ENHANCES SAFETY BY RESTRICTING FORKLIFT TRUCK TRAVEL SPEEDS IN DESIGNATED ZONES

          
          This system offers safe speeds in designated areas whilst keeping productivity at a maximum in lower risk areas. Each gate or exit has a fixed transmitter which can be fitted in various configurations depending on the site requirements. Each truck has a receiver which can trigger additional functionality when it passes a transmitter - when the truck enters the zoned area the system automatically switches to controlled operation and switches back automatically to normal operation when the truck leaves again. In case of any faults or tampering the system can be programmed to default to slow speed.
          
          

          Features

          
          

          • Can be fitted to any vehicle
          • Defined zoned areas
          • Tamper-proof
          • Robust design
          • Easily extendable to additi
            
            Start Smart RFID Access
            

            START SMART

            
            

            HELPS TO ENHANCE SITE SAFETY THROUGH DRIVER ACCESS CONTROL VIA RFID CARDS & FOBS

            
            A vehicle-mounted keypad interfaces with the forklift trucks ignition to only allow truck start-up on detection of a recognized and authorised RFID fob. (also available as pin code entry)
            
            
            

            Features

            
            

            • Suitable for Gas Diesel and Electric trucks
            • Eliminates keys enhancing security
            • Up to 4000 user codes
            • Waterproof and vandal proof IP67 sealed unit
            • Starts vehicle with RFID fob or keypad
            • Low profile design

            Benefits

            
            

            • Increase site safety
            • Theft deterrent
            • Driver accountability

            
            TDS1 RFID entry
            

            THE TDS1

            
            

            THE TDS1 DRIVER ACCESS UNIT INCREASES SAFETY THROUGH CONTROLLED ACCESS AND DRIVER AND TRUCK MONITORING

            
            Provided by our partner in the US Keytroller the TDS1 is a tried and tested keypad which has been adopted by some of the largest forklift truck manufacturers suppliers and users in the world. It provides management information about the fleet assisting logistics professionals in managing their materials handling operation more effectively.
            
            Drivers can log in via a manual key code (4 digits) or an RFID fob available at additional cost.
            
            The system records the driver and truck`s activity which can be downloaded via RS232 onto a laptop/PC. The data can then be reported on to equip fleet managers with information about the truck usage any impacts and more.
            
            

            Fea
            
            TDS601 Fleet Management
            

            THE TDS601

            
            

            PROVIDES:- FLEET MANAGEMENT USABLE CLOUD BASED SOFTWARE DRIVER ACCESS AND IMPACT MONITORING WITH ADDITIONAL COMPATIBILITY ALL FROM ONE UNIT

            
            

            Provided by our partner in the US Keytroller the TDS601 has been adopted by some of the largest forklift truck manufacturers suppliers and users in the world. It provides real-time information about the fleet assisting logistics professionals with managing their operations more effectively.
            
            Drivers can log in via a manual key code (4 digits) or an RFID fob.
            
            The system communicates via Wi-Fi (so no costly data packages or SIM charges) with the cloud based software providing real-time information and automatically generated reports and alerts. A highly flexible daily checks system also allows your truck maintenance procedures to go paper-free with associat
            
            Vision Camera
            

            TRANSMON VISION SYSTEM

            
            

            ENHANCES SITE SAFETY AND EFFICIENCY WHEN WORKING AT HEIGHT BY IMPROVING VISIBILITY

            
            The system offers excellent visibility to the operator from a standard driving position. The camera is located on the vehicle and focuses on the area of sight required with an automatic iris compensating for the change in lighting conditions.The pictures sent live to the TFT 7" colour flat screen located in an unobtrusive position allow the driver to make adjustments to lifting or reversing directions.The system enhances health and safety levels reducing the amount of damage caused by miscalculations made due to human error. Ideal for vehicles operating at height the system is multi-voltage and will also work in cold stores as well as in yards.
            
            Level 1
            Shielded Wired Video Connection Powered from Vehicle
            
            Level 2
            Wireless Fork Mounted Camera
            

            TRANSMON WIRELESS FORK MOUNTED CAMERA

            
            

            WIRELESS FORKLIFT CAMERA

            Transmon Engineering Ltd now offer a unique driver aide. Our wireless fork mounted camera enables the driver a true `fork-eye` vision of the front of the forklift truck. This unique perspective aids drivers by assisting with loading and unloading as well as ensuring the correct fork position when dealing with high level racking and off loading from vehicles. 
            

            
            

            
            The fork mounted camera attached magnetically to enable easy installation as well as re positioning should you require. This magnetic application also helps to minimize damage if there is an accident. The fork camera sends live feed pictures to a 7 inch colour screen monitor mounted unobtrusively within the forklift